In 2010, Brighton and Sussex University Hospitals NHS Trust in England arranged for approximately 1,000 old hard drives to be destroyed, and the job ended up with an individual hired through a subcontractor of its IT provider. In December 2010, a data recovery company bought four of those drives on eBay, and a few months later a university reported that one of its students had bought 20 more. When the UK Information Commissioner's Office examined the student's drives, at least 15 of them still held the trust's data, including medical details of patients (some of them HIV patients), as well as staff National Insurance numbers and home addresses. In June 2012, the regulator fined the trust £325,000, a record at the time.
The trust did not set out to leak anything; it believed the drives were being destroyed, but only basic checks were made on who was doing the work and what happened to each drive, and that gap is behind a lot of disposal leaks. If you are clearing out old PCs, USB sticks and backup tapes, the useful question is which destruction method actually works for each kind of disk, and how you will prove it was done, because a method that is fine for one type of media can leave another readable.
Why Deleted Data Is Still On An Old Disk
When you delete a file or format a disk, the computer usually only removes the pointer that says where the file lives. The data itself stays on the disk until something else is written over it, and anyone with free recovery software can often bring it back. This leftover data is called data remanence.
Large organizations make the same mistake as home users. When the U.S. Government Accountability Office checked computers that the Department of Energy had marked as surplus, it found that some of the excessed computers at DOE headquarters still had information stored on their hard drives, and that the agency lacked standard instructions, checks, and training for clearing them.
Two terms are worth knowing before going further:
- Sanitization: removing data so it cannot be recovered, for example by a verified overwrite, while the disk may still be reused.
- Physical destruction: damaging the disk itself (shredding, crushing, disintegrating, degaussing or burning) so the storage material can no longer be read and the device cannot be used again.
This guide covers physical destruction, which is the right choice when a disk is broken, too old to wipe reliably, or held data that you cannot risk.
Traditional hard drives (HDDs)
A traditional hard drive stores data magnetically on spinning metal or glass platters. Because the data lives on the platter surface, the goal of hard drive destruction is to damage that surface badly enough that no part of it can be read.
- Shredding: an industrial shredder cuts the whole drive, casing and all, into small strips or pieces. This is the most common method for business hard drive shredding because it is fast, it handles large volumes, and it is easy to verify by looking at what comes out.
- Crushing or punching: a machine drives a steel wedge or pin through the drive and bends the platters. The drive will never spin again, but large pieces of platter are left intact, so for highly sensitive data it is better treated as a step before shredding.
- Degaussing: a degausser is a machine that produces a very strong magnetic field and scrambles the magnetic pattern that holds the data. It works on magnetic media only, and the drive is unusable afterwards.
- Disintegration: a disintegrator uses rotating knives and a screen to cut material until the pieces are small enough to pass through the screen. It is mostly used where a security policy asks for very small particles.
SSDs, M.2 sticks and other flash storage
Solid-state drives (SSDs) do not have platters at all. They store data on small flash memory chips, called NAND chips, soldered to a circuit board, and an M.2 drive is the same idea on a board about the size of a stick of gum. This changes how destruction works in a few practical ways.
First, degaussing does nothing to flash memory, because the data is not stored magnetically, so a degaussed SSD can still be fully readable. Second, the data is spread across many chips, and SSDs keep spare areas (over-provisioning) that ordinary software cannot reach, so even a wipe can miss data. Third, each NAND chip is small and tough, and a chip that survives in one piece can be removed and read in a lab with a technique called chip-off recovery, even if the rest of the drive is wrecked.
The practical rule for SSD destruction is that every chip has to be broken, and bending or cracking the board is not enough on its own. That means a shredder or disintegrator set up for flash media, with a cutting size small enough to pass through the chips themselves, or a crusher that breaks the NAND chips and the controller (the chip that manages the drive). Each SSD should also be logged by serial number before it goes in, since a small M.2 stick is easy to lose in a box of loose parts. One of the providers that works this way is Big Data Supply, whose hard drive shredding services include SSD and flash destruction where the drives are crushed or shredded to destroy the NAND chips and controllers, with each drive recorded by serial number and a certificate of destruction issued at the end of the job. The work can be done on-site, where your own team can watch the drives being shredded, or off-site at its R2v3 and RIOS certified facility, which is often the more cost-effective route for larger volumes of hard drive destruction.
USB sticks, SD Cards and External Drives
USB flash drives and SD cards are flash memory, exactly like an SSD, only smaller. A microSD card is basically one chip in a thin plastic shell, so cutting it in half with scissors may not break the part that holds the data. These items should go through a shredder that is rated for small flash media, or go in with the SSDs in a professional destruction batch.
External drives are a different case, because the box is only an enclosure. Open it (or ask your provider to) and check whether it holds a spinning hard drive or an SSD, then treat that drive according to its type.
CDs, DVDs And BLU-Ray Discs
Optical discs store data as tiny marks in a thin reflective layer. They are not magnetic, so degaussing has no effect on them. The reliable options are an optical media shredder, which cuts discs into small particles, or a grinding machine that removes the data layer from the surface. Snapping a disc in half or scratching the label is not enough for anything sensitive, because large sections of the data layer can still be read.
Floppy Disks, Zip Disks And Other Legacy Media
Floppy disks, Zip disks and similar older cartridges are magnetic, so a degausser works on them, and they can also be shredded. The main risk is that people forget these disks exist, so if you find a box of them in a filing cabinet, assume the contents are readable (old floppy drives are still easy to buy) and add them to the destruction inventory.
Backup Tape
Data tape, such as LTO and DLT cartridges, is magnetic and can be degaussed with a degausser that is strong enough for that tape format, or shredded. On LTO cartridges, degaussing also erases the servo tracks the cartridge needs to work, so a degaussed LTO tape is finished. Because tape is usually destroyed in bulk, count the cartridges by barcode or serial number before pickup.
Where Incineration Fits
Incineration means burning media at very high temperatures in a licensed facility. It does destroy the data, but it is a niche option today because of emissions and lost recyclable material, and it should never be attempted at home.
Diy Methods That Fail
Most do-it-yourself methods feel safe without actually destroying all of the data. If you have already tried one of these on a business disk, it is worth sending it for proper hard drive destruction anyway.
- Hammer: a hammer can dent the casing of a hard drive and crack an SSD board, but the platters often survive in large pieces, and NAND chips are small enough that many of them come out intact.
- Drill: drilling a few holes through a hard drive damages only the area around each hole, and most of the platter surface is left untouched. On an SSD, the drill bit can easily miss the chips altogether.
- Microwave: this can cause sparks and fire and releases fumes from CDs and DVDs, and it still does not reliably destroy every part of the data layer.
- Household magnets: fridge magnets and even strong hobby magnets are far weaker than a proper degausser, so they do not reliably erase a hard drive, and they do nothing at all to SSDs, USB sticks or optical discs.
How To Document The Destruction
If you are not able to prove that a disk was destroyed, an auditor will usually treat it as if it was not destroyed. Regulators look for written procedures and records, and the European Data Protection Supervisor's guidance on IT governance, for example, says organizations should put procedures in place for the secure disposal of hardware such as storage media. A workable paper trail usually includes the following:
- An inventory of every disk before it leaves your control, with serial numbers (or tape barcodes), device type and where it came from.
- A chain of custody record, which is a signed log showing who had the disks at each step until they are destroyed.
- The agreed method for each media type (shred, crush, degauss, or a combination), written down before the job starts.
- A certificate of destruction that lists each item by serial number, the method used, the date, and who carried out the work.
- A retention plan for these records, so you can find them in a few years when an auditor or a client asks.
When you choose a provider for hard drive shredding, it is reasonable to ask which recognized certifications it holds (for example R2v3 or NAID AAA) and to see a sample certificate before you sign.
FAQ
Is it safe to destroy a hard drive myself?
A home method rarely destroys all of the platter surface. For business drives, or any drive that held personal, financial or health data, professional hard drive shredding with a certificate is the safer choice.
Does degaussing work on SSDs?
No. Degaussing only works on magnetic media such as hard drives, floppy disks and tape. SSDs, USB sticks and SD cards store data in flash chips, so they need to be shredded or crushed until the chips themselves are broken.
What is a certificate of destruction?
It is the document from the destruction company that lists each item by serial number, with the method and date, and it is your proof for auditors.
How should I destroy old CDs and DVDs?
Use a shredder rated for optical media, or a professional service, since breaking or scratching a disc leaves most of the data layer readable.
Key Takeaways
- Deleting or formatting a disk does not remove the data, and disks that leave your control without a record are behind many disposal leaks.
- Match the method to the media: degaussing works on magnetic disks and tape, but not on SSDs, flash or optical discs.
- With SSDs, M.2 sticks, USB drives and SD cards, the NAND chips themselves have to be broken.
- Hammers, drills, microwaves and household magnets leave readable data behind.
- Keep an inventory, a chain of custody record and a certificate of destruction for every batch.